So I got my sensors reading independently in the serial port but when I upload the Blynk sketch to read them, my app has gauges on V5,V6,and V7 that is supposed to be reading each sensor, and all values are running off the same sensor. The following is the code that I use to get the individual temp sensors to read in serial port…
/* YourDuino Multiple DS18B20 Temperature Sensors on 1 wire
Connections:
DS18B20 Pinout (Left to Right, pins down, flat side toward you)
- Left = Ground
- Center = Signal (Pin 2): (with 3.3K to 4.7K resistor to +5 or 3.3 )
- Right = +5 or +3.3 V
Questions: terry@yourduino.com
V1.01 01/17/2013 ...based on examples from Rik Kretzinger
/*-----( Import needed libraries )-----*/
// Get 1-wire Library here: http://www.pjrc.com/teensy/td_libs_OneWire.html
#include <OneWire.h>
//Get DallasTemperature Library here: http://milesburton.com/Main_Page?title=Dallas_Temperature_Control_Library
#include <DallasTemperature.h>
/*-----( Declare Constants and Pin Numbers )-----*/
#define ONE_WIRE_BUS_PIN 47
/*-----( Declare objects )-----*/
// Setup a oneWire instance to communicate with any OneWire devices
OneWire oneWire(ONE_WIRE_BUS_PIN);
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensors(&oneWire);
/*-----( Declare Variables )-----*/
// Assign the addresses of your 1-Wire temp sensors.
// See the tutorial on how to obtain these addresses:
// http://www.hacktronics.com/Tutorials/arduino-1-wire-address-finder.html
DeviceAddress Probe01 = { 0x28, 0xAC, 0x35, 0xB9, 0x08, 0x00, 0x00, 0x4E };
DeviceAddress Probe02 = { 0x28, 0xE6, 0x15, 0xBD, 0x08, 0x00, 0x00, 0x02 };
DeviceAddress Probe03 = { 0x28, 0xA3, 0x49, 0xBC, 0x08, 0x00, 0x00, 0xA7 };
void setup() /****** SETUP: RUNS ONCE ******/
{
// start serial port to show results
Serial.begin(9600);
Serial.print("Initializing Temperature Control Library Version ");
Serial.println(DALLASTEMPLIBVERSION);
// Initialize the Temperature measurement library
sensors.begin();
// set the resolution to 10 bit (Can be 9 to 12 bits .. lower is faster)
sensors.setResolution(Probe01, 10);
sensors.setResolution(Probe02, 10);
sensors.setResolution(Probe03, 10);
}//--(end setup )---
void loop() /****** LOOP: RUNS CONSTANTLY ******/
{
delay(1000);
Serial.println();
Serial.print("Number of Devices found on bus = ");
Serial.println(sensors.getDeviceCount());
Serial.print("Getting temperatures... ");
Serial.println();
// Command all devices on bus to read temperature
sensors.requestTemperatures();
Serial.print("Probe 01 temperature is: ");
printTemperature(Probe01);
Serial.println();
Serial.print("Probe 02 temperature is: ");
printTemperature(Probe02);
Serial.println();
Serial.print("Probe 03 temperature is: ");
printTemperature(Probe03);
Serial.println();
}//--(end main loop )---
/*-----( Declare User-written Functions )-----*/
void printTemperature(DeviceAddress deviceAddress)
{
float tempC = sensors.getTempC(deviceAddress);
if (tempC == -127.00)
{
Serial.print("Error getting temperature ");
}
else
{
Serial.print("C: ");
Serial.print(tempC);
Serial.print(" F: ");
Serial.print(DallasTemperature::toFahrenheit(tempC));
}
}// End printTemperature
//*********( THE END )***********